MK4duo

New Version 4.3.8

4 votes, average: 5,00 out of 54 votes, average: 5,00 out of 54 votes, average: 5,00 out of 54 votes, average: 5,00 out of 54 votes, average: 5,00 out of 5 (4 votes, average: 5,00 out of 5)
You need to be a registered member to rate this post.
Loading...

Version 4.3.8

  • Add TMC settings to menu LCD
  • Add Adaptive Fan speed
  • Add Request pause to Host
  • Rewrite TMC files
  • Add M92 Subcommand H[microstep] L[Layer wanted]
  • Add to all nextion scroll message By MrGoblin
  • Clear code

New Version 4.3.7

4 votes, average: 3,50 out of 54 votes, average: 3,50 out of 54 votes, average: 3,50 out of 54 votes, average: 3,50 out of 54 votes, average: 3,50 out of 5 (4 votes, average: 3,50 out of 5)
You need to be a registered member to rate this post.
Loading...

### Version 4.3.7
* Add Command:
* G34: Set Delta Height calculated from toolhead position (only DELTA)
* M930: TMC set blank_time.
* M931: TMC set off_time.
* M932: TMC set hysteresis_start.
* M933: TMC set hysteresis_end.
* M934: TMC set fast_decay_time.
* M935: TMC set disable_I_comparator.
* M936: TMC set stealth_gradient.
* M937: TMC set stealth_amplitude.
* M938: TMC set stealth_freq.
* M939: TMC switch stealth_autoscale.
* M940: TMC switch StealthChop.
* M941: TMC switch ChopperMode.
* M942: TMC switch interpolation.
* M524: Abort the current SD print job (started with M24). (Requires SDSUPPORT)
* M223: T[extruder] S[bool] set Filrunout Logic.
* M224: T[extruder] S[bool] set Filrunout Pullup.
* M666: L delta segment per line.
* M851: Set X Y Z Probe Offset in current units, set speed [F]ast and [S]low, [R]epetititons. (Requires Probe)
* M413: S[bool] Enable / Disable Restart Job. (Requires SD_RESTART_FILE)
* M800: S goto to lcd menu. With no parameters run restart commands. (Requires SD_RESTART_FILE)
* Add Text Menu to Nextion Display
* Add sound function
* Add LCD menu for switch Sound [on – silent – off]
* Add pause before deploy/stow for user confirmation
* Add second serial for arduino due
* Add PCF8574 Expansion IO for pin 120 – 121 – 122 – 123 – 124 – 125 – 126 – 127
* Fix M800 for restart job
* Fix error with lcd 44780 with progress bar active
* Fix M205 with Delta and Junction active
* Fix Dogm LCD
* Add Status menu anim option for graphic display
* Add progress bar to heater when heating
* Add Text Menu SD to Nextion
* Add Support USB FLASH DRIVE such as SD
* Fixed GFX overlay with Nextion when printing from USB
* Fix and clear code

New Version 4.3.6

4 votes, average: 3,75 out of 54 votes, average: 3,75 out of 54 votes, average: 3,75 out of 54 votes, average: 3,75 out of 54 votes, average: 3,75 out of 5 (4 votes, average: 3,75 out of 5)
You need to be a registered member to rate this post.
Loading...

### Version 4.3.6
* Make class Mechanics to static
* Add Junction Deviation instead of traditional Jerk limiting
* Add Adaptive multiaxis step smoothing
* Add M205 J – Set Junction Deviation mm
* Add B├ęzier Jerk Control
* Add Safety Timer, after 30 minutes if not printing (SD or M530 S1) the heaters switch off.
* Rewrite SD Restart for auto restart when power loss and return.
* Add command gcode M569 for Stepper driver control: Dir, minimum pulse and maximum rate.
* Add Hysteresis in EEPROM
* Fix and clear code

New Version 4.3.5 stable

7 votes, average: 4,71 out of 57 votes, average: 4,71 out of 57 votes, average: 4,71 out of 57 votes, average: 4,71 out of 57 votes, average: 4,71 out of 5 (7 votes, average: 4,71 out of 5)
You need to be a registered member to rate this post.
Loading...

* Now if a heater does not have a sensor or fails, it will not be used, but it will not kill.
* If the PID autotune is not done, the firmware will not switch the heater on until the autotune is performed. Only if have EEPROM.
* Update Nextion Firmware 4.3″ and 7″
* Fix and clear code

New Version 4.3.4 stable

2 votes, average: 5,00 out of 52 votes, average: 5,00 out of 52 votes, average: 5,00 out of 52 votes, average: 5,00 out of 52 votes, average: 5,00 out of 5 (2 votes, average: 5,00 out of 5)
You need to be a registered member to rate this post.
Loading...

* CaseLight use Neopixel by Original Marlin
* Add command M123 – Set Logic Endstop
* Add command M124 – Set Pullup Endstop
* Add command M603 – Set filament change
* Add command M701 – Load Filament
* Add command M702 – Unload Filament
* Replaced easy bowden with filament change load & unload
* Save Logic and Pullup Endstop to EEPROM
* Fix and clear code